Description

Application Chrysler Aspen 2007-2009 Dodge Dakota 2005-2011 Dodge Durango 2004-2009 Dodge Ram 1500 2002-2010 Mitsubishi Raider 2006-2009 Ram 1500 2011-2013 (2012-2013 RAM 1500 used either 9/16″ or 14×1.5 Studs; Check stud size before ordering) Description Spacer Thickness: 2 inch (51 mm) Bolt pattern: 5x5.5 inch (5x139.7 mm) Center Bore Size: 108 mm Thread Size: 9/16"x18 Torqued Down By Hand At: 135-145 FT/LBS Installation Fits 2002 2003-2013 Dodge Ram 1500 5x5.5 Wheel Spacers (4) 2" Thick 9/16"x18 Application Chrysler Aspen 2007-2009 Dodge Dakota 2005-2011 Dodge Durango 2004-2009 Dodge Ram 1500 2002-2010 Mitsubishi Raider 2006-2009 Ram 1500 2011-2013 (2012-2013 RAM 1500 used either 9/16″ or 14×1.5 Studs; Check stud size before ordering) Description Spacer Thickness: 2 inch (51 mm) Bolt pattern: 5x5.5 inch (5x139.7 mm) Center Bore Size: 108 mm Thread Size: 9/16"x18 Torqued Down By Hand At: 135-145 FT/LBS Installation Loosen the Lug Nuts Common mistake: the first step should be loosening the lug nuts rather than jacking up the vehicle. That’s because you cannot get enough torque on a wheel suspended in the air. So make sure loosening all the wheel lug nuts in turn with a spanner before jacking up the vehicle. Not ification : Just Loosen them, there is no need to unscrew them completely. Jack up the Vehicle, Remove the Wheels Jack up and support the vehicle on the Jack stand, then remove the jack. Finally, remove all nuts and take away the wheels. Clean up the Hub Clean gunk wire brush, put some Loctite on the hub and thread pitch. Avoid collision to the main part and install the wheel spacers to the vehicle. Installing the Wheel Spacers Install the wheel spacers, but use the supplied lug nuts instead of the stock lug nuts. Place the wheel spacer on the studs of the hub. Make sure the studs of wheel spacers face outwards. Later, install the supplied lug nut in a star sequence. Notification: Fix thelugnuts in a diagonal/star pattern in sequence. This will ensure a reliable installation. Do notuse Impact Wrench during installation! It may cause damage to both the vehicle and the product! Please check the exact torque from theinstructions, To prevent loose, thread adhesive can be added during installation. Check the Installation Failure to clean up may cause a gap between the wheel spacer and the hub, which may allow a vibration of vehicle while driving. Place the spacer on the factory hub. The spacer should sit flush with the brake rotor. If there is any gap between the brake rotor and the spacer, even if it is small. Don’t use the spacer! Please be sure to check this. You shouldn’t even be able to slide a piece of paper the spacer on the factory hub. Reinstalling the Wheels Install the wheels to the wheel spacers. Please note that the wheel lug nuts should be fitted in the same way as the wheel spacers lug nuts ---- tighten the lug nuts in diagonal or star sequence. Again it is not necessary to fully fit the nuts in place for this step, just keep them for the next step. Notification : Fix in the order in which the pentagrams are drawn. In the case of six or more holes, fix them roughly in diagonal order. Follow-up Inspection Once everything is in place, drive the vehicle and check for any unusual vibration. Re-torque all lug nuts after 50-100 miles of driving ,then again after 2000-3000 miles. Item Specifics Brand PARTHIGH Manufacturer Part Number PART819514HIGH Number of Pieces 4 Color Silver Material Aluminum Features Easy Installation, Durable, Rust-resistant Coating Placement on Vehicle Front Type Wheel Spacers Item Included Spacer, Lug Bolt, Lug Nut Spacer Thickness 51mm (2 inch) Lug Quantity 5 Stud Grade 10.9 Vehicle Bolt Pattern 5x139.7mm (5x5.5 inch) Wheel Bolt Pattern 5x139.7mm (5x5.5 inch) Center Bore Size 108mm Hubcentric No Thread Pitch 9/16"-18 Torqued Down By Hand At 135-145 FT/LBS Bolt Shank Length 35mm Other Part Number 5x5.5 PCD-9/16" Studs-2" Thick-Wheel Spacers Warning WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. (California Customers should pay more attention about it.) Payment PayPal Only. Only PayPal accept in this selection. Shipping 99% of orders shipped within 24 hours. 2-8 days in transit. Nice and strong packing. UPS , USPS , fedEx comes to be our first choice. Return This item is backed by our 1-year warranty. Refund will be given as money back or replacement Item must be returned in original pacakge and packing the same as received. Seller is responsible for the return if delivered item not the same as described or received damaged. Note: Buyers are responsible for the return shipping cost if the problem ids caused by buyer. We only warranty cost of parts, any installation or other fees are non-refundable. About Us If you have a question about the item you should contact us before bidding. Any problem fund, do contact us please, a ny question or problem will be replied within 24 hours (except the weekend and holiday). Our Customer Service Team is always online to answer. Shop Category Store Home Mirrors Oxygen Sensors Mass Air Flow Sensors Cooling System ◈ Radiators ◈ Cooling Fans ◈ Fan Clutchs ◈ Intercoolers ◈ AC Condenser ◈ Radiator Support Roof Racks Tonneau Covers Window Visors LED Headlight Assembly Fuse Holder Box Windshield Outer Trim Pillar Posts Air Conditioning System ◈ Heater Cores ◈ Blower Motor ◈ Evaporators Running Board Motor Center Console Window Scoop Louver Cover winch Door Handle Ignition Coils Light ◈ 3rd Brake Light ◈ Cab/Side Marker ◈ Instrument Panel Light Window Regulator Brake Calipers & Bracket Strut Mount Cylinder Piston Kit Complete Struts CV Axle Engine Dipstick Ballast Module Throttle Body Shock Struts Air suspension Transfer Case Shift Motor Ignition Coil & Spark Plug Turbocharger Bumper Window switch Suspension Kits Car CV Axle Wheel Spacers Wheel Hub Bearing Coilovers Shock Strut & Suspension Kit Spoilers RV AC PTO Door Lock Actuator Radiator Shutter Garden Water Pump Truck Bed Storage Tool Box Lawn Mower Accessories Golf Cart Accessories Sun Visor Engine Repair Kit Power Steering System Oil Pump & Water Pump VVT Variable Valve Timing Car Moulding Cover Trim Chainsaw Chain Bug Shield Motorcycle Accessories Engine Air Intake & Exhaust Ramps Car Tools Fuel Tank Accessories Dash Board Cover Tensioner Leveling Lift Kit Hydraulic Lifters Coil Spring Spark Plug Brake drum shoe Other Hot Item For 8500-13000LBS Winch Electric Waterproof Soft Winch Cover Dust Cover USD 15.39 For 2010-2015 Chevy Equinox 2008-2010 Malibu 2.4L Oxygen O2 Sensor 02 Upstream USD 14.97 For 1999-2006 Chevrolet Silverado 1500 Left+Right Side View Door Mirrors Manual USD 39.75 A/C Blower Motor Resistor For 1999 00 01-2002 Chevrolet Silverado 1500 2500 Kit USD 45.99 4x Roof Rack Cover Rail End Shell Cap Replacement For Toyota Highlander 2008-13 USD 21.44 New List Item 92087 Heater Core Part For 2007 08 09 10 11-12 Dodge Liberty Nitro Santa Fe Jeep USD 24.46 For 2018-2021 Volkswagen Atlas Radiator Aluminum CU13755 Fast Shipping USD 78.68 Driver Side Sun Visor Fits Mazda CX-9 Sport 3.7L 2010-2015 USD 26.88 Radiator 2585 For 2003-2006 Kia Sorento With stainless steel Hose Clamps USD 74.99 Power Mirror Heated Signal Puddle Light For Dodge Ram 2019-2022 Temp Sensor+BSM USD 229.75 Excellent Delivery Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us Fits 2002 2003-2013 Dodge Ram 1500 5x5.5 Wheel Spacers (4) 2" Thick 9/16"x18 Application Chrysler Aspen 2007-2009 Dodge Dakota 2005-2011 Dodge Durango 2004-2009 Dodge Ram 1500 2002-2010 Mitsubishi Raider 2006-2009 Ram 1500 2011-2013 (2012-2013 RAM 1500 used either 9/16″ or 14×1.5 Studs; Check stud size before ordering) Description Spacer Thickness: 2 inch (51 mm) Bolt pattern: 5x5.5 inch (5x139.7 mm) Center Bore Size: 108 mm Thread Size: 9/16"x18 Torqued Down By Hand At: 135-145 FT/LBS Installation Loosen the Lug Nuts Common mistake: the first step should be loosening the lug nuts rather than jacking up the vehicle. That’s because you cannot get enough torque on a wheel suspended in the air. So make sure loosening all the wheel lug nuts in turn with a spanner before jacking up the vehicle. Not ification : Just Loosen them, there is no need to unscrew them completely. Jack up the Vehicle, Remove the Wheels Jack up and support the vehicle on the Jack stand, then remove the jack. Finally, remove all nuts and take away the wheels. Clean up the Hub Clean gunk wire brush, put some Loctite on the hub and thread pitch. Avoid collision to the main part and install the wheel spacers to the vehicle. Installing the Wheel Spacers Install the wheel spacers, but use the supplied lug nuts instead of the stock lug nuts. Place the wheel spacer on the studs of the hub. Make sure the studs of wheel spacers face outwards. Later, install the supplied lug nut in a star sequence. Notification: Fix thelugnuts in a diagonal/star pattern in sequence. This will ensure a reliable installation. Do notuse Impact Wrench during installation! It may cause damage to both the vehicle and the product! Please check the exact torque from theinstructions, To prevent loose, thread adhesive can be added during installation. Check the Installation Failure to clean up may cause a gap between the wheel spacer and the hub, which may allow a vibration of vehicle while driving. Place the spacer on the factory hub. The spacer should sit flush with the brake rotor. If there is any gap between the brake rotor and the spacer, even if it is small. Don’t use the spacer! Please be sure to check this. You shouldn’t even be able to slide a piece of paper the spacer on the factory hub. Reinstalling the Wheels Install the wheels to the wheel spacers. Please note that the wheel lug nuts should be fitted in the same way as the wheel spacers lug nuts ---- tighten the lug nuts in diagonal or star sequence. Again it is not necessary to fully fit the nuts in place for this step, just keep them for the next step. Notification : Fix in the order in which the pentagrams are drawn. In the case of six or more holes, fix them roughly in diagonal order. Follow-up Inspection Once everything is in place, drive the vehicle and check for any unusual vibration. Re-torque all lug nuts after 50-100 miles of driving ,then again after 2000-3000 miles. Item Specifics Brand PARTHIGH Manufacturer Part Number PART819514HIGH Number of Pieces 4 Color Silver Material Aluminum Features Easy Installation, Durable, Rust-resistant Coating Placement on Vehicle Front Type Wheel Spacers Item Included Spacer, Lug Bolt, Lug Nut Spacer Thickness 51mm (2 inch) Lug Quantity 5 Stud Grade 10.9 Vehicle Bolt Pattern 5x139.7mm (5x5.5 inch) Wheel Bolt Pattern 5x139.7mm (5x5.5 inch) Center Bore Size 108mm Hubcentric No Thread Pitch 9/16"-18 Torqued Down By Hand At 135-145 FT/LBS Bolt Shank Length 35mm Other Part Number 5x5.5 PCD-9/16" Studs-2" Thick-Wheel Spacers Warning WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. (California Customers should pay more attention about it.) Payment PayPal Only. Only PayPal accept in this selection. Shipping 99% of orders shipped within 24 hours. 2-8 days in transit. Nice and strong packing. UPS , USPS , fedEx comes to be our first choice. Return This item is backed by our 1-year warranty. Refund will be given as money back or replacement Item must be returned in original pacakge and packing the same as received. Seller is responsible for the return if delivered item not the same as described or received damaged. Note: Buyers are responsible for the return shipping cost if the problem ids caused by buyer. We only warranty cost of parts, any installation or other fees are non-refundable. About Us If you have a question about the item you should contact us before bidding. Any problem fund, do contact us please, a ny question or problem will be replied within 24 hours (except the weekend and holiday). Our Customer Service Team is always online to answer. All rights reserved.